Gas Turbine: Operation & Maintenance - YOGYAKARTA (Pasti Jalan)

Gas Turbine: Operation & Maintenance - YOGYAKARTA

Hotel  IBIS  Yogyakarta| Yogyakarta  11- 14 April  2011|IDR  6.500.000,- (Pasti Jalan)
Bandung| Bandung 25 - 27 Mei  2011|IDR  7.250.000,-
Hotel  IBIS  Yogyakarta| Yogyakarta  3 - 6 Mei  2011|IDR  6.500.000,-
Hotel  IBIS  Yogyakarta | Yogyakarta  21 – 24 Juni  2011|IDR 6.500.000,-

 

DESCRIPTION

The purpose of this course is to introduce personnel to the turbo machinery package, explain system functions and interface, introduce proper operation procedures, and acquaint the student with basic maintenance procedures.

At the conclusion of this course the student should have a basic understanding of turbine engine theory, be familiar with the Solar turbine package and its components, understand satisfactory operation of the package, and be aware of routine maintenance procedures.

This course does not prepare the student to accomplish advanced maintenance and troubleshooting functions. Solar turbine package are built to exacting specifications and more extensive training is required before a serviceman is qualified to perform major repairs and adjustments.

 

PARTICIPANTS

1. Maintenance Engineer/ Superintendent/ Supervisor


2. Rotating Engineer/ Superintendent/Supervisor


3. Power Plant Engineer/ Superintendent / Supervisor

 

COURSE OUTLINE

• Introduction and General Description


• Turbine Engine


• Pneumatic and Hydraulic Start System


• Air System


• Gas Fuel System


• Lube Oil System


• The Gas Boost Compressor


• Turbine Control System


• Turbotronic System


• Operating Procedures


• Performance Analysis


• Safety Requirement


• Preventive Maintenance


• Corrective Maintenance

 

METODE

lecturing, workshop, interactive consultation, and case study

 

INSTRUKTUR

Dr. Ir Viktor Malau DEA

 

WAKTU

• Yogyakarta 11 - 14 April 2011


• Bandung  25 - 27 April 2011


• Yogyakarta  `3 - 6 Mei2011


• Yogyakarta  21 – 24 Juni  2011

 

TEMPAT

• Hotel Ibis Yogyakarta


• Bandung

 

INVESTASI

Yogyakarta

• IDR  6.500.000 – (non residential )


• (termasuk picking-up service dari Bandara/Stasiun KA ke hotel, training modul, training kit, 2x coffee break, 1x lunch, souvenir, dan sertifikat)

Bandung

• Course fee sebesar:  Rp 7.250.000 per peserta (Non-Residensial). Minimal pendaftaran peserta 3 (tiga) orang

Pelatihan & Sertifikasi K3 Teknisi Listrik - Sertifikasi Depnakertrans (PASTI JALAN)

Pelatihan & Sertifikasi K3 Teknisi Listrik

(Ref. Kep Dirjen Pembinaan Hub. Industrial & Pengawasan Ketenagakerjaan No.311/BW/2002)

Hotel Sofyan Betawi, Jakarta dan Politeknik Negeri Bandung |11 s.d 14 April 2011| 08.00 – 17.00 | Rp 5.500.000,- (Pasti Jalan)
Hotel Patra Jasa Cempaka Putih, Jakarta dan Politeknik Negeri Bandung |13s.d 16 Juni 2011| 08.00 – 17.00 | Rp 5.500.000,-
Hotel Patra Jasa Cempaka Putih, Jakarta dan Politeknik Negeri Bandung |19 s.d 22 September 2011| 08.00 – 17.00 | Rp 5.500.000,-
Hotel Patra Jasa Cempaka Putih, Jakarta dan Politeknik Negeri Bandung |07 s.d 10 November  2011| 08.00 – 17.00 | Rp 5.500.000,-
Hotel Patra Jasa Cempaka Putih, Jakarta dan Politeknik Negeri Bandung |05  s.d 08 Desember  2011| 08.00 – 17.00 | Rp 5.500.000,-

 

Materi  Pelatihan

• Peraturan Perundangan Keselamatan dan Kesehatan Kerja


• Dasar – dasar Keselamatan dan Kesehatan Kerja Listrik


• Dasar – dasar Teknik  Instalasi Listrik


• Identifikasi  Bahaya Listrik


• Sistem  Pengamanan


• Persyaratan  Instalasi  Listrik Ruang Khusus


• Sistem  Proteksi  Bahaya  Petir


• Klasifikasi  Pembebanan


• Pengukuran  Listrik (teorik & praktek)


• Pertolongan  Pertama  Kecelakaan  Listrik


• Evaluasi

Tanggal & Tempat Pelatihan

 

Jam:

08.00 – 17.00

Tanggal & Tempat

Tanggal         :

• 11 s.d 14 April 2011


• 13s.d 16 Juni 2011


• 19 s.d 22 September 2011


• 07 s.d 10 November  2011


• 05  s.d 08 Desember  2011

Jam              :  08.00 – 17.00

Tempat         :  Hotel Sofyan Betawi

Jl. Dr. Sahardjo No. 191, Jakarta Selatan

Politeknik Negeri Bandung (POLBAN) –  Jawa Barat (Praktek)

Instruktur

Para Praktisi dari Depnakertrans RI dan Politeknik Negeri Bandung (Polban)

Biaya  Pelatihan

• Rp 5.500.000,- (Lima Juta Lima Ratus Ribu Rupiah).


• Biaya tersebut sudah termasuk Training kit, Modul, Buku PUIL 2000, Soft copy materi, Kartu Kewenangan dan Sertifikat dari Depnakertrans RI, 2x Coffee break, Lunch, Akomodasi praktek (penginapan (twinshare), dinner & breakfast) selama 1 malam di Bandung,


• Tidak termasuk pajak – pajak.

PELATIHAN & SERTIFIKASI OPERATOR CRANE - Bersertifikasi Depnakertrans

PELATIHAN & SERTIFIKASI OPERATOR CRANE
Balai Air Bersih, Bekasi | 09  s.d 12  Mei  2011 |  08.00 – 16.00 | Rp 3.000.000,-
Balai Air Bersih, Bekasi | 06 s.d 09 Juni 2011 |  08.00 – 16.00 | Rp 3.000.000,-
Balai Air Bersih, Bekasi | 04  s.d 07 Juli 2011 |  08.00 – 16.00 | Rp 3.000.000,-
Balai Air Bersih, Bekasi | 12  s.d 15  September 2011 |  08.00 – 16.00 | Rp 3.000.000,-
Balai Air Bersih, Bekasi | 10  s.d 13  Oktober  2011 |  08.00 – 16.00 | Rp 3.000.000,-
Balai Air Bersih, Bekasi |  14  s.d 17 November  2011 |  08.00 – 16.00 | Rp 3.000.000,-
Balai Air Bersih, Bekasi | 12  s.d 15 Desember  2011 |  08.00 – 16.00 | Rp 3.000.000,-

 

Tujuan dan Manfaat

Pelatihan ini bertujuan untuk meningkatkan pengetahuan dan ketrampilan dalam mengoperasikan crane sehingga operator akan bertanggungjawab, berdisiplin, serta memahami dan mengerti persyaratan keselamatan & kesehatan kerja (K3) dalam mengoperasikan crane yang lebih efisien produktif dan aman.

 

Materi  Pelatihan

1. Undang – Undang No.01 Tahun 1970


2. Kebijakan Depnaker


3. Peraturan Menteri Tenaga Kerja No.05 Tahun 1985


4. Pengetahuan Dasar crane


5. Penggerak Mula (motor bakar)


6. Dasar – dasar hidrolik


7. Sebab – sebab kecelakaan pada pengoperasian crane


8. Pengoperasian yang aman


9. Dasar pengukuran kapasitas & signal (aba – aba)


10. Tali kawat baja & alat bantu angkat


11. Perawatan dan pemeliharaan crane


12. Praktek

 

Metode Pelatihan

Ceramah, diskusi & praktek

 

Instruktur

Instruktur yang akan memberikan pelatihan ini berasal dari Departemen Tenaga Kerja yang memiliki keahlian khusus di bidang K3 dan para counterpart yang telah ditraining di Jepang dan dibantu oleh tenaga professional ex. United Tractor.

 

Peserta Pelatihan

Untuk operator kelas 1 :

1. Sekurang – kurangnya pendidikan SLTA


2. Berpengalaman minimal 5 tahun sebagai operator dengan kapasitas 50 ton.

Untuk operator kelas 2 :

1. Sekurang – kurangnya pendidikan SLTP


2. Berpengalaman minimal 3 tahun sebagai operator dengan kapasitas 25 s.d 50 ton.

Untuk operator kelas 3 :

1. Sekurang – kurangnya pendidikan SLTP


2. Berpengalaman minimal 1 tahun sebagai operator dengan kapasitas 25 ton.

 

Tempat  & Tanggal Pelatihan

• 09  s.d 12  Mei  2011


• 06 s.d 09 Juni 2011


• 04  s.d 07 Juli 2011 -


• 12  s.d 15  September 2011


• 10  s.d 13  Oktober  2011


• 14  s.d 17 November  2011


• 12  s.d 15 Desember  2011

 

Jam                  :

08.00 – 16.00

 

Tempat             :

Balai Air Bersih Bekasi
Jl. Chairil Anwar I No.1
Margahayu – Bekasi Timur

 

Biaya  Pelatihan

• Biaya pelatihan sebesar Rp 3.000.000,- (Tiga Juta Rupiah).


• Biaya tersebut sudah termasuk Fee Instruktur Class room dan Lapangan, Penggandaan materi, Training kit, 2X Coffee Break, Lunch, Sertifikat, SIO dan  Buku Kerja dari Departemen Tenaga Kerja RI.


• Tidak termasuk pajak – pajak.

 

Pelatihan & Sertifikasi Operator Boiler kelas 1 (kapasitas lebih besar dari 10 ton) - Sertifikasi Depnakertrans

Pelatihan & Sertifikasi Operator Boiler kelas 1 (kapasitas > 10 ton)

Pusat KK & Hiperkes (tentative), Jakarta |Jakarta,25 – 30 April 2011 s.d 02-03 Mei 2011| 08.00 – 17.00 | Rp 3.750.000,-



 

Tujuan & Manfaat

Pelatihan ini bertujuan untuk memberikan pengetahuan dan ketrampilan dalam teknik pengoperasian  pesawat uap secara aman, benar dan sesuai dengan peraturan perundangan di bidang Keselamatan dan Kesehatan Kerja (K3) yang berlaku.

Materi Pelatihan

1. Kebijakan Keselamatan dan Kesehatan Kerja


2. Undang – Undang No 1 tahun 1970 tentang Keselamatan Kerja


3. Undang – Undang dan Peraturan Uap tahun 1930


4. Permenaker No. 01/MEN/1988 tentang Kualifikasi dan Syarat – syarat Operator Pesawat Uap


5. Dasar – Dasar K3


6. Jenis Pesawat Uap dan Cara Kerjanya


7. Cara Pengoperasian Pesawat Uap


8. Fungsi Appendages/Perlengkapan Pesawat Uap


9. Air pengisi ketel uap & cara pengolahannya


10. Sebab – Sebab Peledakan Pesawat Uap


11. Persiapan Pemeriksaan dan Pengujian Pesawat Uap


12. Pengetahuan Instalasi listrik untuk Ketel Uap


13. Pengetahuan bahan


14. Peninjauan konstruksi pesawat uap


15. Pemeriksaan secara  tidak merusak


16. Perpindahan Panas


17. Pengetahuan bahan bakar dan Pembakaran


18. Analisa kecelakaan peledakan


19. Cara Inspeksi dan Reparasi Pesawat Uap


20. Praktek

Metode Penyajian

Ceramah, Diskusi, Simulasi dan Praktek lapangan yang akan disajikan instruktur dari Depnakertrans dan para profesional. Pelatihan dengan ujian teori dan praktek untuk mendapatkan Surat Ijin Operasi.

Persyaratan Peserta

Berpenidikan minimal SMA atau STM dan Peserta adalah calon operator pesawat uap yang belum memiliki SIO kelas I sesuai dengan Permenaker no. Per.01/Men/1988 tentang kualifikasi dan syarat – syarat operator pesawat uap atau peserta yang sudah mempunyai SIO kelas II dan ingin melanjutkan Operator Boiler kelas I

Tanggal & Tempat Pelatihan

Tanggal:

• 25 – 30 April s.d 02-03 Mei 2011

Jam        :

08.00 – 17.00

 

Tempat :

Pusat KK & Hiperkes (tentative)
Jl. A Yani Kav 69 – 70, Cempaka Putih
Jakarta Pusat

 

Biaya Pelatihan

• Rp 3.750.000,- (Tiga Juta Tujuh Ratus Lima Puluh Ribu Rupiah).


• Biaya tersebut sudah termasuk Fee Instruktur, Penggandaan Materi, Training Kit, 2X Coffee Break, Lunch, Sertifikat dan SIO dari Depnakertrans RI.


• Biaya tidak termasuk pajak – pajak.

LV AND MV GENERATOR (Operation, Protection and Maintanance)

LV AND MV GENERATOR (Operation, Protection and Maintanance)

Hotel Jayakarta, Bandung | 8 – 12 Agustus 2011 | Rp 7.250.000/person





OBJECTIVES:

Pelatihan ini dimaksudkan untuk meningkatkan pengetahuan dan wawasan tentang aspek-aspek engineering dari LV and MV generator. Topik pelatihan ditekankan pada operasi dan pemeliharaan generator.







CAKUPAN MATERI TRAINING:

1. Generator construction


2. Generator Principles


3. Generator Characteristics


4. Excitation system


5. Generator Operation


6. Abnormal conditions


7. Generator protection


8. Generator Maintenance

INSTRUCTOR : Ir. Hasan Surya, MT. and Team

Ir. Hasan Surya, MT. is graduated from Bandung Institute of Technology (ITB) for Bachelor and Master program at Electrical Engineering department. Since 1985 till now Ir. Hasan Surya is lecturer at electrical engineering Polytechnique ITB (POLBAN)  and he is a head of department at electrical engineering. Ir. Hasan Surya have delivered some training topics related to his major expertise for  many companies in Indonesia. Ir. Hasan Surya have been researching in electrical engineering and becoming speaker for some conference. Ir. Hasan Surya has also worked for some companies or institution so he has got much real experiences  and now he is ready to share his knowledge and experiences to industrial world throught training class.




VENUE

Hotel Jayakarta, Bandung




TRAINING DURATION

5 days






TRAINING TIME

1. 8 – 12 Agustus 2011

INVESTATION PRICE/PERSON

1. Rp 7.450.000/person (full fare)  or


2. Rp 7.250.000/person (early bird, payment 1 week before training) or


3. Rp 6.950.000/person (if there are 3 persons or more from the same company)

FACILITIES FOR PARTICIPANTS

1. Training Module


2. Flash Disk contains training material


3. Certificate


4. Stationeries: NoteBook and Ballpoint


5. T-Shirt


6. Bag


7. Training Photo


8. Training room with Full AC facilities and multimedia


9. Lunch and twice coffeebreak every day of training


10. Qualified Instructor


11. Transportation for participants from hotel of participants to/from hotel of training – VV (if minimal participants is 4 persons from the same company)

CENTRIFUGAL PUMPS : SELECTION, OPERATION AND MAINTENANCE

CENTRIFUGAL PUMPS : SELECTION, OPERATION AND MAINTENANCE

Yogyakarta| Batch I: 26-29 April 2011| 08:00-16:00 WIB |Rp 4.500,000,-/peserta (Non resindential)
Yogyakarta|Batch II: 14 – 16 Juni 2011| 08:00-16:00 WIB |Rp 4.500,000,-/peserta (Non resindential)

 

Description

Assuming that a plant is a body of human being, pumps are the "heart" of the body. Those play very important and vital roles to flow the "blood" of a plant. In every plant or production operation system, we find pumps. However, unlike bolts and nuts, neither industry nor production-operation management will put pumps in stock. It is NOT cost effective and is very uncommon practice to put a complete set of pump in the warehouse stock due to financial reasons.
Therefore, properly specifying, selecting, installing, operating and maintaining pumps are very significant and are very important steps to have "trouble free" during the entire life of the plant operation. Thus, proper maintenance and operation is also the key to reduce the entire cost of the plant and production operation system.
This five-day training will provide a comprehensive knowledge and understanding of pump selection, installation, operation, and maintenance program. The training will concentrate in centrifugal pump as they are the most common one used in the industries and day life.

 

Objective

• Refresh the knowledge of the participants on fluid mechanic and pump characteristics


• Understand centrifugal-pump basic-system design, selection, operation, treatment and installation


• Learn the critical symptoms of pump operation


• Enhance the knowledge on pump sealing and rolling elements


• Gain additional knowledge on inspection and maintenance of centrifugal pumps


• Knowledge sharing among the participants and instructors

 

Course Outline

1. Basic Theory of Fluid Mechanics

• Physical properties of incompressible fluid


• Static fluid


• Basic flow of incompressible fluid


• Basic fluid dynamic


• Basic fluid energy process

2. Basic Theory of Centrifugal Pump and Installation

• Head or energy requirement of the installation


• The principle of energy transfer in centrifugal pump


• Characteristic of pump and its installation (Capacity, Head, and Efficiency)
  Combination of pump and installation


• Pump specification


• Pump selection based on capacity, head, and efficiency


• Pump arrangement; series and parallel


• Suction analysis (Cavitations and NPSH)

3. Basic Theory of Reciprocating Pump and Installation

• Type of reciprocating pumps


• Comparison of centrifugal and reciprocating pumps.


• Discharge of a reciprocating pump.


• Slip of the pump.


• Power required driving a reciprocating pump.


• Indicator diagram of a reciprocating pump.


• Variation of pressure in the suction and delivery pipes due to acceleration of the   piston.


• Effect of the acceleration of the piston on the indicator diagram.


• Maximum speed of the rotating crank.


• Effect of friction in the suction and delivery pipes, on the indicator diagram.


• Effect of fitting air vessels on the suction and delivery pipes of a reciprocating pump.


• Maximum speed of rotating crank with air vessels.


• Work done against friction with/without and air vessels.


• Flow of water into and from the air vessel, fitted to the delivery pipe of a reciprocating pump.


• Multiple cylinder pumps.

4.Critical Symptoms of Pump Operation

• Cavitations


• Water hammer


• Over pressure


• Negative pressure


• Surging


• Pressure fluctuation

5.Operation

• Procedure to run and stop the pump


• Controlling the capacity


• Hazard prevention


• Automatic operation


• Centrifugal pump application


• General notes on pre-starting checks General notes on pump lubrication


• General notes on pump operation


• General notes on pump maintenance


• Process pump bearing

6.Centrifugal Pump Sealing

• Seals principles and practice


• Pump shaft sealing


• Mechanical seals in the process industry

7.Rolling Element Bearings in Centrifugal Pump

• Principles of centrifugal pumps


• Angular contact ball bearing in centrifugal pump


• Double row angular contact ball bearing

8.Selecting Multiphase Pumps

9.Inspection and Maintenance of Pump

• Preliminary inspection


• Operating condition inspection


• Spare parts handling


• Inspection (visual, dimensional and non-destructive test)


• Mechanical and electrical run-out


• Dynamic balancing per API-610


• Rotor assembly


• Trouble shooting

10.Practice of centrifugal pump performance measurement at Fluid Lab. Mechanical Engineering UGM

 

What Should Attends

• Fresh Mechanical or Rotating Engineers, Engineering and Construction Engineers, Project Engineer


• Production Operators, Technicians, Asset Management Team members, Maintenance and Operation Personnel who are responsible for the


• Selection, Sizing, Specifying, Installation, Testing, And Maintenance Of pumping system.


• Experienced professionals who want to refresh or broaden their understanding of pumps


• Professionals with little to moderate production facility design and or production operation back ground


• Other professionals who want better understanding of the subject

 

Instruktur :

• Dr. Ir. Rini Darmastiti, M.Sc


• Dr. Deendarlianto, M.Eng

(Expert in Mechanical Engineering)

Course Method

• Presentation


• Discuss


• Case Study


• Evaluation


• Lab Study

 

Fee:

• Pelatihan Reguler  (NON RESIDENTIAL)


• Rp. 4.500.000,-/nett per participant  non  residential


• Rp 4.000.000,-/3 peserta dari perusahaan yang sama

 

Course Fee  :

• Batch I: 26-29 April 2011


• Batch II: 14 – 16 Juni 2011


• Yogyakarta

 

Fascilities

• Module / Handout


• Sertifikat


• Souvenir


• Training Kit

 

Programmable Logic Controller Using Siemens S7- 400 *Sertificate by Siemens*

Programmable Logic Controller Using Siemens S7- 400 *Sertificate by Siemens*

Grand Cempaka Hotel Jakarta dan worklab siemens| April 25 s.d 29 , 2011 | Rp 7.500,000,-/peserta (Non Residential)
Grand Cempaka Hotel Jakarta dan worklab siemens|Juli 18  s.d 22 , 2011 | Rp 7.500,000,-/peserta (Non Residential)

 

Introduction
This section will begin with a discussion of basic theory of operation and how it is used to control a process. It will also identify potential applications and relate how PLC control compares with traditional methods of control. A discussion of the benefits of  PLC control will follow.

 

Objective
PLC Training is designed to instruct electrical control professionals on how to successfully integrate a PLC into actual day-to-day industial electrical processes. It not only deals with the hardware and software, but all the surrounding systems that must be compatible to achieve a safe and reliable control system.
PLC Training is also designed to help delegates keep abreast of the latest Siemens’s PLC technologies and techniques available in this area, this tutorial offers an excellent opportunity for delegates to ask specific questions and exchange ideas relating to their own applications.

 

Hardware Configuration
This section will describe the various components used in the formulation of a PLC control system for Siemens S7-400. Included will be methods to select the correct features and capabilities to match the process requirements.

• CPU sizes and types


• Backplanes


• Power supplies


• I/O module types

 

Installation and Wiring Considerations
There are necessary steps that must be taken to ensure that the control system will be correctly installed to provide safe and reliable operation. Installation recommendations and techniques will be given for the following:

• Power and grounding


• Enclosures


• Input devices and wiring methods


• Output devices and wiring methods

 

Commissioning
This section will discuss the methods used and preparations that should be made to guarantee a smooth and troublefree system start-up.

 

Safety Issues and Techniques
This section will define the major safety issues relating to control systems. A number of techniques will be discussed to address these issues including:

• Solid state switching


• E-Stops


• Power-up delays


• Equipment re-starting


• Watchdog circuits


• MCR circuits

 

PLC Numbering Systems
PLC control system hardware and software use alternate numbering systems. The delegate will be exposed to the different base systems and how to convert to and from the decimal format.

 

Programming Siemens S7-400
The delegates will be instructed in the commands and logic necessary to assemble a basic PLC program to control an industrial process. The delegate will perform a simple programming exercise.

 

Interactive Discussion
This will be an opportunity for delegates to interact and trade relevant stories and experiences.

 

Programming Software
Various types of programming software will be introduced to the delegates. Techniques for simple program development and downloading will be demonstrated. Topics will include:

• Program functions


• Program keying and development


• Connecting to the PLC


• Set-up


• Program downloading


• Monitoring and diagnostics

Hardware will be available so that the delegate can get some hands on experience programming and downloading.

 

Structured Programming
The concept of structured and block programming will be explained. Methods and techniques will be described which can be used to organize and standardize PLC programs so that they can be easily understood.

 

Documentation Strategies
The various types of documentation required for effective installation, maintenance, and troubleshooting will be reviewed.

 

Programmable Logic Controller Troubleshooting
Troubleshooting a Programmable Logic Controller-based control system has its challenges and advantages. The necessary tools and techniques required to perform this will be covered. The use of programming software to monitor and diagnose process and hardware problems will be demonstrated.

 

Operator Interfaces
The various types of operator interfaces and how they can be used to enhance the control and diagnostic abilities of the Programmable Logic Controller will be discussed.

 

Data Acquisition
Methods of collecting and storing process data using the PLC s7-400 and peripheral computer stations will be described. Advanced data representation, graphics, and calculations using the computer to enhance the adaptive control capability of the Programmable Logic Controller based system will also be covered.

 

Who Should Attend

• PLC Engineering and design personnel


• Maintenance and technical services personnel


• Process and operations personnel


• Technical and process managers


• Engineering and design personnel


• Electrical consulting engineers


• Electrical contractors

 

Metode Kursus

• Presentation


• Discuss


• Case Study


• Evaluation


• Simulation *Laboratory/Work Shop*

 

Koordinator

Ir. Edwin Ardiansya & Team dari Siemens

• Expert in Motors, Drives, Automation using DCS & PLC


• System Integrator Siemens.

 

Biaya :

• Biaya Kursus: Rp 7.500,000,-/peserta (Non Residential)


• Special Rate Rp  7.000,000,- for min. 3 participant

 

Fasilitas

• Module / Handout


• Sertifikat


• Souvenir


• Training Kit

 

Maintenance Control and Monitoring

Maintenance Control and Monitoring

Aryaduta Hotel / Grand Flora Hotel*, Jakarta | May 28 th, 2011 | Rp. 2.450.000, -  (Full Fare)

Latar Belakang

Salah satu masalah yang sering muncul dalam persoalan perawatan adalah lemahnya bidang control dan monitoring terhadap pelaksanaan kegiatan perawatan.

Sering sekali persoalan ini muncul justru di saat maintenance schedule dan maintenance instruction sudah tersedia dengan baik. Personil perawatan menganggap lingkup pekerjaan semakin banyak dan luas, akhirnya orientasi pelaksanaan kegiatan hanya “ asal gugur kewajiban “. Padahal hakekat yang paling penting adalah justru dari kesungguhan melaksanakan kegiatan perawatan dengan baik.

Tentu kita tidak bisa menyederhanakan persoalan dari sudut pandang personilnya semata, tanpa diimbangi oleh pengetahuan dan keterampilan yang cukup mengenai hal ini. Kegiatan perawatan yang sering “di-nomor dua-kan” dibanding bagian produksi, secara psikologis sering memukul mental personil perawatan sebagai objek pelengkap penderita. Jika kondisi ini dibiarkan terlalu lama, maka kebiasaan kerja perawatan yang asal gugur kewajiban” akan menjadi perilaku yang biasa. Hal ini tentu sangat merugikan dan tidak diharapkan oleh managemen perusahaan manapun. Dalam pelatihan ini perserta akan diberi pemahaman konsep dan implementasinya.

 

Manfaat

Mengerti konsep monitoring dan mampu melakukan control perawatan dengan baik dan benar, sehingga tercipta suatu system perawatan yang efektif dari sisi perencanaan dan pelaksanaan.

 

 

Materi Bahasan

• Terminology  of Maintenance ( Corrective, Preventive, Predictive )


• Principles of  Control & Monitoring


• Administration Approach


• Psychological approach


• Control by Maintenance Cost Reports


• Human Factors in Maintenance Activity


• Maintenance Supervisory by Maintenance Sheets


• Maintenance Work Measurement and Standardization

 

Metode :

• Ceramah dan Pelatihan
  

 

Workload Leader

DR. Ir. Dede Farhan Aulawi, MM, CHT      ( Praktisi Perawatan Mesin Industri )

 

 

Fee :

• Rp. 1.750.000, -  (Registration 3 person/more; payment before May 21st, 2011)


• Rp. 1.950.000, -  (Reg before May 14th, 2011; payment before May 21st, 2011)


• Rp. 2.450.000, -  (Full Fare)

 

Venue

• The Aryaduta Suites Hotel Semanggi/ Grand Flora Hotel

 

Gearbox Technology: Design, Analysis, Testing, Maintenance, Lubrication, and Failure - YOGYAKARTA

Gearbox Technology: Design, Analysis, Testing, Maintenance, Lubrication, and Failure - YOGYAKARTA

Hotel  IBIS  Yogyakarta| Yogyakarta  10 – 13 Mei 2011 |IDR  6.500.000,-
Hotel  IBIS  Yogyakarta | Yogyakarta  21 – 24 Juni  2011|IDR 6.500.000,-

 

OBJECTIVES

1. Understand the standard of setting up plan for gearbox


2. Make the gearbox recalculation and planned


3. Classification and analysis of gear


4. Gear Box Maintenance


5. Measurement Technique and gear Box testing


6. Gearbox failure Analysis

 

COURSE OUTLINE

A. Introduction

• Application of Gear System


• Gear Classification


• Gear Nomenclature


• Power Train


• Gear Standard


• Unit System

B. Gear Analysis

• Power Train


• Stress and Deflection


• Strength/ Allowable Stress


• Fatigue


• Gear Design Life

C. Gear Design

• Spur Gear


• Helix Gear


• Gearbox


• Case Study

• o Spur Gear Design


• o Helix Gear Design

D. Measurement and Testing

• Principles of Measurement


• Geometry Measurement


• Vibration Measurement


• Noise Measurement


• Gear System Efficiency


• Gear Testing

E. Maintenance and Lubrication

• Maintainability and Maintenance


• Maintenance in Product Life Cycle


• Life Cycle Cost


• Why We Need the Maintenance


• Maintenance Category


• Gear Maintenance


• Lubrication


• Gear Lubrication


• Power Losses in Gear


• Type of Gear Lubrication


• Lubrication for Loaded Gear


• Influence of Gear Lubrication on Surface Distress

F. Gear Failure

• Failure Classification


• Wear


• Surface Fatigue


• Plastic Flow


• Breakage


• Hertz Contact


• Case Study of Gear Failure

 

PARTICIPANTS

Mechanical Engineers, Maintenance Engineers and supervisors, Service Engineers and supervisors and everyone who want to enlarge their knowledge

 

METODE

lecturing, workshop, interactive consultation, and case study

 

INSTRUKTUR

Dr. Ir Viktor Malau DEA

 

WAKTU

• Yogyakarta  10 – 13 Mei 2011


• Yogyakarta  21 – 24 Juni  2011

 

TEMPAT

Hotel Ibis Yogyakarta

 

INVESTASI

• IDR  6.500.000 – (non residential )


• (termasuk picking-up service dari Bandara/Stasiun KA ke hotel, training modul, training kit, 2x coffee break, 1x lunch, souvenir, dan sertifikat)

 

Gas Engine: Operation & Maintenance - YOGYAKARTA

Gas Engine: Operation & Maintenance - YOGYAKARTA

Hotel Grage Ramayana Yogyakarta | Yogyakarta  12 – 15 Mei 2011|IDR  5.000.000,-
Hotel Grage Ramayana Yogyakarta | Yogyakarta  21 – 24 Juni  2011|IDR  5.000.000,-

 

DESCRIPTION

Pelatihan Gas Engine Maintenance and Operation akan membahas topik-topik pemeliharaan dan prinsip dasar stoichiometric mesin gas dan teknik pengendalian system pembakaran. Materi mencakup berbagai tipe mesin berbahan bakar gas termasuk Series Lean Burn dengan Electronic Ignition Systems (EIS) dan Air/Fuel Ratio Control otomatis. Mesin berbahan bakar gas memiliki karakteristik khusus, sehingga orang-orang yang terlibat dalam pengoperasian maupun pemeliharaan harus bebar-benar memahami secara detail prinsip kerja dari mesin tersebut. Sehingga mesin dapat beroperasi secara maksimal yang pada kahirnya akan meningkatkan produktivitas kerja sesuai dengan yang diharapkan. Dengan melakukan pemeliharaan secara rutin maka umur pakai mesin akan lebih lama dan kerusakan dapat diketahui secara lebih dini.

OBJECTIVES

1. Memahami operasi mesin berbahan bakar gas


2. Memahami tipe-tipe mesin berbakar gas dan prinsip kerjanya


3. Memahami pemeliharaan mesin berbahan bakar gas

 

OUTLINE

1. Fuel Background Story & Safety Procedure


2. Major Component


3. System Operation


4. Air Fuel Ratio Adjustment


5. Wastegate Adjustment


6. Using Oxygen Meter


7. Using BTU Graph


8. Power Screw Adjustment


9. Differential Pressure Adjustment


10. Using Fuel Usage Guide


11. Ignition Timing Adjustment


12. Data Interpretation


13. Set up & Performance Test


14. Setting Safety Device & Verification

 

METODE

lecturing, workshop, interactive consultation, and case study

 

INSTRUKTUR

Dr. Ir Viktor Malau DEA

 

WAKTU

• Yogyakarta  `12 – 15 Mei 2011


• Yogyakarta  21 – 24 Juni  2011

 

TEMPAT

Hotel Grage Ramayana Yogyakarta

 

INVESTASI

• IDR  5.000.000 – (non residential )


• (termasuk picking-up service dari Bandara/Stasiun KA ke hotel, training modul, training kit, 2x coffee break, 1x lunch, souvenir, dan sertifikat)

 

PNEUMATIK LANJUTAN

PNEUMATIK LANJUTAN

Politeknik Negeri Bandung, Bandung| 11 s.d 15 APRIL  2011 | 08.00 – 16.00 | Rp 6.000.000,-
Politeknik Negeri Bandung, Bandung| 18 s.d 22 JULI  2011 | 08.00 – 16.00 | Rp 6.000.000,-
Politeknik Negeri Bandung, Bandung | 10 s.d 14 OKTOBER   2011 | 08.00 – 16.00 | Rp 6.000.000,-

 

Tujuan Pelatihan

Memberikan suatu wawasan industri dalam merancang kontrol pneumatik yang lebih komplek akibat sinyal – sinyal bentrok dalam perancangan suatu sistem

 

Persyaratan

Mempunyai latar belakang mekanik secara umum

 

Materi  & Praktek

• Review pneumatik dasar, valve 5/2, 3/2, monostable, bistable, dan logika AND, OR.


• Pemahaman gerak sekuensial.


• Metode : diagram cascade, shift register.


• Safety Regulation: emergency stop, start, stop, single/continuous.


• Simulasi rangkaian kontrol dan troubleshooting.

 

Ruang Lingkup Peserta

 

Insinyur, pengawas dan teknisi yang bergerak di bidang perancangan penggunaan &  pemeliharaan sistem kontrol pneumatik (max. 6 Orang; 1 Work bench/computer per 2 orang).

 

Instruktur

• Adri Maldi S., MSc


• Ir. Ali Mahmudi, M eng


• Ir. Aris Suryadi

 

Tanggal & Tempat Pelatihan

Tanggal     :

• 11 s.d 15 APRIL  2011


• 18 s.d 22 JULI  2011


• 10 s.d 14 OKTOBER   2011

 

Jam            : 08.00 – 16.00
Tempat     :Politeknik Negeri Bandung Jl. Ciwaruga - Bandung

 

Biaya Pelatihan

• Rp 6.000.000,- (Enam Juta Rupiah).


• sudah termasuk
  
  
  
  • Hand out,
  
  
  • Training kit,
  
  
  • 2x Coffee break,
  
  
  • Lunch
  
  
  • dan Sertifikat.
  
  
  
  


• Tidak termasuk pajak - pajak.

 

Pelatihan Operator Boiler kelas 2 (kapasitas < 10 ton) - Bersertifikasi Depnakertrans

Pelatihan Operator Boiler kelas 2 (kapasitas < 10 ton)

Pusat KK & Hiperkes, Jakarta (tentative) |25 s.d 30 April 2011| 08.00 – 17.00 | Rp 3.250.000,-
Pusat KK & Hiperkes, Jakarta (tentative) |02 s.d 07 Mei 2011| 08.00 – 17.00 | Rp 3.250.000,-
Pusat KK & Hiperkes, Jakarta (tentative) |04 s.d 09 Juli  2011| 08.00 – 17.00 | Rp 3.250.000,-
Pusat KK & Hiperkes, Jakarta (tentative) |12 s.d 17 Sept 2011| 08.00 – 17.00 | Rp 3.250.000,-
Pusat KK & Hiperkes, Jakarta (tentative) |14 s.d 19 November 2011| 08.00 – 17.00 | Rp 3.250.000,-

 

Tujuan & Manfaat

Pelatihan ini bertujuan untuk memberikan pengetahuan dan ketrampilan dalam teknik pengoperasian  pesawat uap secara aman, benar dan sesuai dengan peraturan perundangan di bidang Keselamatan dan Kesehatan Kerja (K3) yang berlaku.

 

Materi Pelatihan

1. Kebijakan Keselamatan dan Kesehatan Kerja


2. Undang – Undang No 1 tahun 1970 tentang Keselamatan Kerja


3. Undang – Undang dan Peraturan Uap tahun 1930


4. Permenaker No. 01/MEN/1988 tentang Kualifikasi dan Syarat – syarat Operator Pesawat Uap


5. Dasar – Dasar K3


6. Jenis Pesawat Uap dan Cara Kerjanya


7. Cara Pengoperasian Pesawat Uap


8. Fungsi Appendages/Perlengkapan Pesawat Uap


9. Air pengisi ketel uap & cara pengolahannya


10. Sebab – Sebab Peledakan Pesawat Uap


11. Persiapan Pemeriksaan dan Pengujian Pesawat Uap


12. Pengetahuan instalasi listrik untuk Ketel Uap


13. Pengetahuan Bahan Bakar dan Pembakaran


14. Praktek

 

Metode Penyajian

Metode pelatihan ini adalah ceramah, diskusi, simulasi dan praktek lapangan yang akan disajikan instruktur dari Depnakertrans dan para profesional. Pelatihan dengan ujian teori dan praktek untuk mendapatkan Surat Ijin Operasi.

 

Persyaratan Peserta

Berpendidikan minimal SLTP dan  peserta adalah calon operator pesawat uap yang belum memiliki SIO sesuai dengan Permenaker no. Per.01/Men/1988 tentang Kualifikasi dan syarat – syarat operator pesawat uap

 

Tanggal & Tempat Pelatihan

Tanggal  :

• 25 s.d 30 April 2011


• 02 s.d 07 Mei 2011


• 04 s.d 09 Juli  2011


• 12 s.d 17 Sept 2011


• 14 s.d 19 November 2011

 

Jam        :

08.00 – 17.00

 

Tempat  :

Pusat KK & Hiperkes
Jl. A Yani Kav 69 - 70
Cempaka Putih - Jakarta Pusat

 

Biaya Pelatihan

• Rp3.250.000,- (Tiga Juta Dua Ratus Lima Puluh Ribu Rupiah).


• Biaya diatas termasuk Fee Instruktur Class Room dan Lapangan, Penggandaan Materi, Training Kit, 2X Coffee Break, Lunch, Sertifikat  dan SIO  dari Depnakertrans RI.


• Tidak termasuk  Pajak – Pajak.

 

COMPRESSOR : Operation, Maintenance and Troubleshooting

COMPRESSOR : Operation, Maintenance and Troubleshooting
Hotel Golden Flower, Bandung| 30 Mei – 1 Juni 2011| Rp 5.500.000/person
Hotel Golden Flower, Bandung|24 – 26 Oktober 2011| Rp 5.500.000/person

TUJUAN TRAINING :

Training ini bertujuan untuk :

1. Memahami prinsip kerja kompresor.


2. Memahami kelebihan dan kekurangan masing-masing jenis kompresor.


3. Memahami spesifikasi masing-masing jenis kompresor.


4. Memahami spesifikasi sistem instalasi.


5. Memahami parameter operasi.


6. Mampu mengevaluasi unjuk kerja kompresor.


7. Mampu menangani kelainan opersai (trouble).


8. Memahami dan mampu melaksanakan perawatan.


9. Mampu meramalkan unjuk kerja kompresor termodifikasi.

 

CAKUPAN MATERI TRAINING :

1.    Kompresor volumetrik (positive displacement compressors) dan kompresor dinamik (turbo).
2.    Komponen kompresor volumetrik dan kompresor dinamik.
3.    Sifat-sifat gas dan campuran gas serta proses kompresi.
4.    Pembangkitan tekanan
5.    Operasi kompresor

• Normal


• Perubahan kecepatan putar


• Perubahan beban


• Surging


• Chocking

6.    Prestasi kompresor :

• Kerugian-kerugian energi


• Neraca energi


• Efisiensi kompresor


• Kurva-kurva prestasi

7.    Prestasi kompresor :

• Kerugian-kerugian energi


• Neraca energi


• Efisiensi kompresor


• Kurva-kurva prestasi

8.    Komponen kritis kompresor dinamik :

• Sudu (vanes)


• Sudu pengarah ( intake guide vane)


• Bantalan ( journal and thrust bearing)


• Seal oil and buffer gas system

9.    Komponen-komponen dan peralatan bantu (auxiliaries)

• Sistem pelumasan


• Pendingin pelumas (oil cooler)


• Penjerat air (demister)


• Pemisah pelumas (oil separator)

10.    Kecepatan putar kritis
11.    Instalasi kompresor
12.    Operasi kompresor

• Start-up


• loading


• Shut-down

13.    Maintenance
14.    Trouble-shooting
15.    Diskusi

 

Instructor

Ir. Pawito Merto Sontowiro, Msc

Ir. Pawito Merto Sontowiro, Msc adalah alumnus Teknik Mesin ITB dan sejak tahun 1973 menjadi dosen di jurusan tersebut sampai sekarang. Beliau adalah kepala Laboratorium Energi termal Teknik Mesin Institut Teknologi Bandung, Beliau juga pernah menjabat sebagai ketua jurusan Teknik Mesin ITENAS Bandung, Pernah mengajar di SESKOAD, Pernah mengajar di prokerma depnaker-ITB, prokerma PLN-ITB. Beliau juga pernah memperdalam keilmuan di luar negeri seperti bidang Coal Energy , Argonne, Chicago, Ill., USA, bidang Combustion, Petc, Pittsburgh, Pa, USA dan Pinch Technology, Asian-Australia Energy Cooperation. Bidang spesialisasi Beliau adalah Boiler, Turbin Uap/Gas, Pompa, Kompresor, Konversi Energi dan analisis energy.. Pernah mengerjakan projek pada bidang Modifikasi Sistem Pembakaran Lokomotip D-52, Modifikasi Sistem Penunjang Boiler, Analisis Sistem Boiler, dan lain-lain. Beliau adalah trainer produktif, pernah mengajar training  untuk banyak perusahaan di Indonesia seperti Chevron Indonesia Company, Chevron pacific Indonesia, Total E&P Indonesie, PT. Pusri, PT. Pupuk Kaltim, PT. BADAK, Depnaker RI, PT. KKA Aceh, KDTP I Bontang, UP-IV PERTAMINA, Kalimantan Prima Coal (KPC), PLN, PT. PERTAMINA, DIKTI, BPPT, PT. Indonesia Power, Pertamina UP II, PT. Pupuk Kujang, PT. Petroleum Consolindo, PT. Indah Kiat Pulp and Paper, PT. Krakatau Steel, PLTU Paiton, PLTU Suralaya, PT. Kaltim Pasifik Amoniak, CNOOC  SES LTD, PLTGU  BEKASI POWER, PT. INDO FUJI ENGINEERING, PT. CONOCO PHILLIPS, dan lain-lain.  Pak Pawito juga aktif menulis buku seperti Perpindahan Kalor, Konversi Energi, Thermodinamika, Pembangkit Uap, Bahan Bakar Dan Pelumas, dan Pompa. Beliau telah melakukan banyak penelitian disertai publikasi ilmiahnya.

 

 

VENUE

Hotel Golden Flower, Bandung

TRAINING DURATION

3 days

TRAINING TIME

1. 30 Mei – 1 Juni 2011


2. 24 – 26 Oktober 2011

INVESTATION PRICE/ PERSON

1. Rp 5.500.000/person (full fare)  or


2. Rp 5.250.000/person (early bird, payment 1 week before training) or


3. Rp 4.950.000/person (if there are 3 persons or more from the same company)

FACILITIES FOR PARTICIPANTS

1. Training Module


2. Flash Disk contains training material


3. Certificate


4. Stationeries: NoteBook and Ballpoint


5. T-Shirt


6. Bag


7. Training Photo


8. Training room with Full AC facilities and multimedia


9. Lunch and twice coffeebreak every day of training


10. Qualified Instructor


11. Transportation for participants from hotel of participants to/from hotel of training – VV (if minimal participants is 4 persons from the same company)

RECOMMENDATION FOR PARTICIPANTS

For practice session: every participant is recommended to bring laptop/notebook for software installation and practice

HIGH PRESSURE PUMP (HPP): OPERATION, MAINTENANCE AND TROUBLESHOOTING

HIGH PRESSURE PUMP (HPP): OPERATION, MAINTENANCE AND TROUBLESHOOTING

Hotel Golden Flower, Bandung| 18 – 21 April 2011 | Rp 7.250.000/person
Hotel Golden Flower, Bandung|12 – 15 September 2011| Rp 7.250.000/person

 

CAKUPAN MATERI TRAINING :

1. Introduction :

• Review Pompa


• Parameter pompa


• Kapasitas


• Head dan Efisiensi

1. Konstruksi pompa sentrifugal single and multi stages pump


2. Pembangkitan Head


3. Hubungan dimensi, putaran dan head pompa sentrifugal


4. Pompa bertingkat, seri dan parallel


5. Sistem Pemipaan dan Kerugian Head Sistem (instalasi)


6. Operasi pompa; kesetimbanagan pompa dan instalasi


7. Sisi Hisap; Net Positive Suction Lift dan kavitasi


8. Minimum Flow


9. Bearings dan Pelumasan


10. Vibrasi


11. Start-Up dan Shut-Down


12. Material Komponen Pompa


13. Maintenance


14. Trobleshooting; kelainan operasi, penyebab dan penanganan


15. Diskusi

 

Instructor

Ir. Pawito Merto Sontowiro, Msc adalah alumnus Teknik Mesin ITB dan sejak tahun 1973 menjadi dosen di jurusan tersebut sampai sekarang. Beliau adalah kepala Laboratorium Energi termal Teknik Mesin Institut Teknologi Bandung, Beliau juga pernah menjabat sebagai ketua jurusan Teknik Mesin ITENAS Bandung, Pernah mengajar di SESKOAD, Pernah mengajar di prokerma depnaker-ITB, prokerma PLN-ITB. Beliau juga pernah memperdalam keilmuan di luar negeri seperti bidang Coal Energy , Argonne, Chicago, Ill., USA, bidang Combustion, Petc, Pittsburgh, Pa, USA dan Pinch Technology, Asian-Australia Energy Cooperation. Bidang spesialisasi Beliau adalah Boiler, Turbin Uap/Gas, Pompa, Kompresor, Konversi Energi dan analisis energy.. Pernah mengerjakan projek pada bidang Modifikasi Sistem Pembakaran Lokomotip D-52, Modifikasi Sistem Penunjang Boiler, Analisis Sistem Boiler, dan lain-lain. Beliau adalah trainer produktif, pernah mengajar training  untuk banyak perusahaan di Indonesia seperti Chevron Indonesia Company, Chevron pacific Indonesia, Total E&P Indonesie, PT. Pusri, PT. Pupuk Kaltim, PT. BADAK, Depnaker RI, PT. KKA Aceh, KDTP I Bontang, UP-IV PERTAMINA, Kalimantan Prima Coal (KPC), PLN, PT. PERTAMINA, DIKTI, BPPT, PT. Indonesia Power, Pertamina UP II, PT. Pupuk Kujang, PT. Petroleum Consolindo, PT. Indah Kiat Pulp and Paper, PT. Krakatau Steel, PLTU Paiton, PLTU Suralaya, PT. Kaltim Pasifik Amoniak, CNOOC  SES LTD, PLTGU  BEKASI POWER, PT. INDO FUJI ENGINEERING, PT. CONOCO PHILLIPS, dan lain-lain.  Pak Pawito juga aktif menulis buku seperti Perpindahan Kalor, Konversi Energi, Thermodinamika, Pembangkit Uap, Bahan Bakar Dan Pelumas, dan Pompa. Beliau telah melakukan banyak penelitian disertai publikasi ilmiahnya.

 

VENUE

Hotel Golden Flower, Bandung

 

TRAINING DURATION

4 days

 

TRAINING TIME

1. 18 – 21 April 2011


2. 12 – 15 September 2011

 

INVESTATION PRICE/ PERSON

1. Rp 7.250.000/person (full fare)  or


2. Rp 7.000.000/person (early bird, payment 1 week before training) or


3. Rp 6.750.000/person (if there are 3 persons or more from the same company)

 

FACILITIES FOR PARTICIPANTS

1. Training Module


2. Flash Disk contains training material


3. Certificate


4. Stationeries: NoteBook and Ballpoint


5. T-Shirt


6. Bag


7. Training Photo


8. Training room with Full AC facilities and multimedia


9. Lunch and twice coffeebreak every day of training


10. Qualified Instructor


11. Transportation for participants from hotel of participants to/from hotel of training – VV (if minimal participants is 4 persons from the same company)

 

RECOMMENDATION FOR PARTICIPANTS

For practice session: every participant is recommended to bring laptop/notebook for software installation and practice

DISTRIBUTION SYSTEM PROTECTION

DISTRIBUTION SYSTEM PROTECTION

Hotel Golden Flower, Bandung |6 – 10 June 2011| Rp 7450.000/person
Hotel Golden Flower, Bandung |7 – 11 November 2011 | Rp 7.450.000/person

TUJUAN TRAINING:

Pelatihan ini dimaksudkan untuk meningkatkan pengetahuan dan wawasan secara komprehensif tentang aspek-aspek sistem distribusi tenaga listrik. Topik pelatihan ditekankan pada tehnik dalam melakukan proteksi dan melakukan koordinasi peralatan proteksi untuk melindungi peralatan distribusi sistem Tenaga Listrik yang ada di industri.

 

TRAINING MATERIAL OUTLINE/CAKUPAN MATERI TRAINING :

TRAINING MATERIAL OUTLINE :

1.    Fundamentals of Protection

• Need for protection


• Types of fault


• Circuit breaker control circuits


• Protection relay fundamentals


• solid state relays


• Digital protection devices.

2.    Overcurrent Protection

• Over current protection devices characteristics


• Application to Industrial Electrical Utilities protection


• Application to line protection


• Function of directional relays


• Relay settings

3.    Differential Protection

• Principle of differential relays


• Application to transformer protection


• Application to generator protection


• Application to bus protection


• Pilot wire differential protection

4.    Coordination of Protection Devices

• Primary protection and back-up


• Need for coordination of settings


• Relay/fuse coordination


• Relay/recloser coordination


• Fuse/recloser coordination.

5.    Overvoltage Protection

• Lighting surges


• Overvoltage protection relays


• Surge arresters


• Insulation coordination

 

SIAPA SEBAIKNYA MENGIKUTI TRAINING INI? :

Pelatihan ini diberikan pada para tehnisi, operator maupun supervisor yang bekerja dibidang ketenaga listrikan untuk menangani masalah proteksi, keselamatan, pengujian peralatan/system distribusi tenaga listrik di industri

 

Training instructor

Ir. Hasan Surya, MT. is graduated from Bandung Institute of Technology (ITB) for Bachelor and Master program at Electrical Engineering department. Since 1985 till now Ir. Hasan Surya is lecturer at electrical engineering Polytechnique ITB (POLBAN)  and he is a head of department at electrical engineering. Ir. Hasan Surya have delivered some training topics related to his major expertise for  many companies in Indonesia. Ir. Hasan Surya have been researching in electrical engineering and becoming speaker for some conference. Ir. Hasan Surya has also worked for some companies or institution so he has got much real experiences  and now he is ready to share his knowledge and experiences to industrial world throught training class.

 

VENUE :

Hotel Golden Flower, Bandung

 

TRAINING DURATION :

5 days

 

TRAINING TIME :

1. 6 – 10 June 2011


2. 7 – 11 November 2011

 

INVESTATION PRICE/PERSON :

1. Rp 7.450.000/person (full fare)  or


2. Rp 7.250.000/person (early bird, payment 1 week before training) or


3. Rp 6.950.000/person (if there are 3 persons or more from the same company)

 

FACILITIES FOR PARTICIPANTS :

1. Training Module


2. Flash Disk contains training material


3. Certificate


4. Stationeries: NoteBook and Ballpoint


5. T-Shirt


6. Bag


7. Training Photo


8. Training room with Full AC facilities and multimedia


9. Lunch and twice coffeebreak every day of training


10. Qualified Instructor


11. Transportation for participants from hotel of participants to/from hotel of training – VV (if minimal participants is 4 persons from the same company)

VARIABLE SPEED DRIVES: Operation, Protection and Maintanance

VARIABLE SPEED DRIVES: Operation, Protection and Maintanance
Hotel Golden Flower, Bandung|21 – 24 February 2011 | Rp7.450.000/person
Hotel Golden Flower, Bandung|4 – 8 Juli 2011| Rp7.450.000/person
Hotel Golden Flower, Bandung| 28 November – 2 Desember 2011| Rp7.450.000/person

 

OBJECTIVES

Pelatihan ini memberikan pengetahuan dan ketrampilan tentang operasi dan pemeliharaan Pengendali Kecepatan otomatis yang dapat diatur dari motor-motor listrik di Industri. Pelatihan ditekankan pada pemilihan pemilihan jenis VSD, unjuk kerja dan cara pengoperasian/instalasi motor listrik serta cara-cara melakukan pengujian komponen, instalasi, proteksi dan trouble shooting pada VSD. Dengan demikian diharapkan peserta pelatihan memahami mekanisme kerja dan pemeliharaan Speed Drives secara komprehensif

 

TUJUAN TRAINING :

Training yang akan diadakan mempunyai tujuan seperti yang tertera pada butir-butir berikut :

1. Memahami prinsip kerja pompa.


2. Memahami kelebihan dan kekurangan masing-masing jenis pompa.


3. Memahami spesifikasi masing-masing jenis pompa.


4. Memahami spesifikasi sistem instalasi.


5. Memahami parameter operasi.


6. Mampu mengevaluasi unjuk kerja pompa.


7. Mampu menangani kelainan opersai (trouble).


8. Memahami dan mampu melaksanakan perawatan.


9. Mampu meramalkan unjuk kerja pompa termodifikasi

 

WHO SHOULD ATTEND

Minimum SLTA : untuk para operator, teknisi, engineer yang ingin mengetahui/mendalami tehnik pengoperasian dan pemeliharaan sistem pengendali kecepatan.

 

TRAINING MATERIAL OUTLINE

1. Karakteristik motor-motor Listrik Industri


2. Kinerja Motor Listrik pada kondisi abnormal


3. Prinsip Pengendalian kecepatan Motor Listrik di Industri


4. Macam-macam Pengendali Kecepatan


5. Konverter-konverter Statis


6. Pengujian Komponen


7. Prinsip Sistem kendali Otomatis


8. Pengendali KecepatanMotor DC


9. Pengendali Kecepatan Motor Induksi


10. Instalasi dan proteksi


11. Langkah-langkah Pemeriksaan VSD


12. Praktikum Pengendali kecepatan

 

INSTRUCTOR

Ir. Hasan Surya, MT. is graduated from Bandung Institute of Technology (ITB) for Bachelor and Master program at Electrical Engineering department. Since 1985 till now Ir. Hasan Surya is lecturer at electrical engineering Polytechnique ITB (POLBAN)  and he is a head of department at electrical engineering. Ir. Hasan Surya have delivered some training topics related to his major expertise for  many companies in Indonesia. Ir. Hasan Surya have been researching in electrical engineering and becoming speaker for some conference. Ir. Hasan Surya has also worked for some companies or institution so he has got much real experiences  and now he is ready to share his knowledge and experiences to industrial world throught training class.

 

VENUE

Hotel Golden Flower, Bandung

 

TRAINING DURATION

5 days

 

TRAINING TIME

1. 21 – 25 Februari 2011


2. 4 – 8 Juli 2011


3. 28 November – 2 Desember 2011

 

INVESTATION PRICE/PERSON

1. Rp 7.450.000/person (full fare)  or


2. Rp 7.250.000/person (early bird, payment 1 week before training) or


3. Rp 6.950.000/person (if there are 3 persons or more from the same company)

 

FACILITIES FOR PARTICIPANTS

1. Training Module


2. Training CD Contains Training Material


3. Certificate


4. Stationeries: NoteBook and Ballpoint


5. Jacket or Waistcoat or T-Shirt


6. Bag or Backpackers


7. Training Photo


8. Training Room with Full AC Facilities and multimedia


9. Once lunch and twice coffeebreak every day of training


10. Qualified  instructor


11. Transportation for participants from hotel of participants to/from venue of training(if minimal number of participants from one company is 4 persons)

 

PUMP : OPERATION, MAINTENANCE AND TROUBLESHOOTING

PUMP :  OPERATION, MAINTENANCE AND TROUBLESHOOTING

Hotel Golden Flower, Bandung|21 – 24 February 2011 | Rp7.250.000/person
Hotel Golden Flower, Bandung|13 – 16 June 2011 | Rp7.250.000/person
Hotel Golden Flower, Bandung| 7 – 10 November 2011| Rp7.250.000/person

TUJUAN TRAINING :

Training yang akan diadakan mempunyai tujuan seperti yang tertera pada butir-butir berikut :

1. Memahami prinsip kerja pompa.


2. Memahami kelebihan dan kekurangan masing-masing jenis pompa.


3. Memahami spesifikasi masing-masing jenis pompa.


4. Memahami spesifikasi sistem instalasi.


5. Memahami parameter operasi.


6. Mampu mengevaluasi unjuk kerja pompa.


7. Mampu menangani kelainan opersai (trouble).


8. Memahami dan mampu melaksanakan perawatan.


9. Mampu meramalkan unjuk kerja pompa termodifikasi

 

WHO SHOULD ATTEND

• Process Engineers


• Instrument Engineers


• Material Engineers


• Structure Engineers


• Electrical Engineers


• Mechanical Engineers


• Safety and Environment Engineers

 

TRAINING MATERIAL OUTLINE

CAKUPAN MATERI TRAINING :

1. Komponen utama pompa dan fungsinya


2. Komponen-komponen pembantu : diffuser, packing/sealing, bearings dan balancing drum/piston


3. Pompa sentrifugal, aliran campuran dan aksial


4. Kecepatan spesifik


5. Faktor faktor penentu besarnya head, kapasitas aliran dan prestasi pompa


6. Sistem : head statik dan dinamik (head mayor dan minor)


7. Titik kerja ( matching point) operasi


8. Operasi tunggal, seri dan paralel


9. Kendala-kendala operasi :
   
   
   1. kavitasi : NPSH tersedia, NPSH persyaratan
   
   
   2. tinggi hisap
   
   
   3. minimum flow
   
   
   4. water-hammer
   
   
   5. seizure (panas, gesekan, kegagalan pelumasan dll).
   
   

10. Operasi :

1. start-up dan shut-down


2. kegagalan operasi (trouble-shooting) : gejala, sebab dan tindakan

11. Kecepatan putar kritis
12. Instalasi pompa dan sistem
13. Perawatan : routine, terjadwal, break-down
14. Material
15. Studi kasus
16. Diskusi

 

INSTRUCTOR

Ir. Pawito Merto Sontowiro, Msc adalah alumnus Teknik Mesin ITB dan sejak tahun 1973 menjadi dosen di jurusan tersebut sampai sekarang. Beliau adalah kepala Laboratorium Energi termal Teknik Mesin Institut Teknologi Bandung, Beliau juga pernah menjabat sebagai ketua jurusan Teknik Mesin ITENAS Bandung, Pernah mengajar di SESKOAD, Pernah mengajar di prokerma depnaker-ITB, prokerma PLN-ITB. Beliau juga pernah memperdalam keilmuan di luar negeri seperti bidang Coal Energy , Argonne, Chicago, Ill., USA, bidang Combustion, Petc, Pittsburgh, Pa, USA dan Pinch Technology, Asian-Australia Energy Cooperation. Bidang spesialisasi Beliau adalah Boiler, Turbin Uap/Gas, Pompa, Kompresor, Konversi Energi dan analisis energy.. Pernah mengerjakan projek pada bidang Modifikasi Sistem Pembakaran Lokomotip D-52, Modifikasi Sistem Penunjang Boiler, Analisis Sistem Boiler, dan lain-lain. Beliau adalah trainer produktif, pernah mengajar training  untuk banyak perusahaan di Indonesia seperti Chevron Indonesia Company, Chevron pacific Indonesia, Total E&P Indonesie, PT. Pusri, PT. Pupuk Kaltim, PT. BADAK, Depnaker RI, PT. KKA Aceh, KDTP I Bontang, UP-IV PERTAMINA, Kalimantan Prima Coal (KPC), PLN, PT. PERTAMINA, DIKTI, BPPT, PT. Indonesia Power, Pertamina UP II, PT. Pupuk Kujang, PT. Petroleum Consolindo, PT. Indah Kiat Pulp and Paper, PT. Krakatau Steel, PLTU Paiton, PLTU Suralaya, PT. Kaltim Pasifik Amoniak, CNOOC  SES LTD, PLTGU  BEKASI POWER, PT. INDO FUJI ENGINEERING, PT. CONOCO PHILLIPS, dan lain-lain.  Pak Pawito juga aktif menulis buku seperti Perpindahan Kalor, Konversi Energi, Thermodinamika, Pembangkit Uap, Bahan Bakar Dan Pelumas, dan Pompa. Beliau telah melakukan banyak penelitian disertai publikasi ilmiahnya.

 

 

VENUE

Hotel Golden Flower, Bandung

 

TRAINING DURATION

4 days

 

TRAINING TIME

21 – 24 February 2011
13 – 16 June 2011
7 – 10 November 2011

 

INVESTATION PRICE/PERSON

1. Rp 7.250.000/person (full fare)  or


2. Rp 7.000.000/person (early bird, payment 1 week before training) or


3. Rp 6.750.000/person (if there are 3 persons or more from the same company)

 

FACILITIES FOR PARTICIPANTS

1. Training Module


2. Training CD Contains Training Material


3. Certificate


4. Stationeries: NoteBook and Ballpoint


5. Jacket or Waistcoat or T-Shirt


6. Bag or Backpackers


7. Training Photo


8. Training Room with Full AC Facilities and multimedia


9. Once lunch and twice coffeebreak every day of training


10. Qualified  instructor


11. Transportation for participants from hotel of participants to/from venue of training(if minimal number of participants from one company is 4 persons)

 

PEMINDAHAN TANAH MEKANIS

PEMINDAHAN TANAH MEKANIS

Hotel Golden Flower Bandung | 11 – 13 Oktober 2010 | Rp 5.450.000,-

 

TRAINING MATERIAL OUTLINE :

1. Alat-alat Pemindahan Tanah mekanis


2. Land Clearing


3. Pemuatan


4. Pengangkutan


5. Dumping

 

INSTRUKTUR TRAINING

Ir. A. M. Ulum A. Gani, M.Sc. ,who is graduated from Geofisika Tambang ITB Bandung, was born in Watan Soppeng, 18 December 1949, he is peneliti utama at Pusat Penelitian Geoteknologi Lembaga Ilmu Pengetahuan Indonesia (LIPI). 1990 – 1993 he was becoming head of  Laboratorium Eksplorasi Mineral, Balitbang Mineral, Puslitbang Geoteknologi, Lembaga Ilmu Pengetahuan Indonesia (LIPI), and 1993-1997 he was becoming head of Laboratorium Pemanfaatan Bitumen, Puslitbang Geoteknologi –LIPI Bandung. He is lecturer at Sekolah Tinggi Teknologi Mineral Indonesia (STTMI) Bandung since 1991-now and becoming head of department at Teknik Pertambangan, Sekolah Tinggi Teknologi Mineral Indonesia (STTMI) Bandung. He has performed many seminars related to his expertise.  Ir.A.M.Ulum A. Gani, M.Sc. has researched and published the results numerous number. At campus Sekolah Tinggi Teknolgi Mineral Indonesia (STTMI) Bandung he teachs for several subjects as follows Pengantar Teknologi Mineral, Bahan Galian Industri, Pembukaan Tambang bawah Tanah, Ventilasi Tambang, Seminar Tambang, and Kerja Praktek. His this much real experiences will be shared with participants in training class.

 

VENUE :

Hotel Golden Flower Bandung

 

TRAINING DURATION :

3 days

 

TRAINING TIME :

11 – 13 Oktober 2010

 

INVESTATION PRICE/PERSON :

1. Rp 5.450.000/person (full fare)  or


2. Rp 5.250.000/person (early bird, payment before 4 October 2010) or


3. Rp 4.950.000/person (if there are 3 persons or more from the same company)

 

FACILITIES FOR PARTICIPANTS:

1. Training Module


2. Training CD Contains Training Material


3. Certificate


4. Stationeries: NoteBook and Ballpoint


5. Jacket or Waistcoat or T-Shirt


6. Bag or Backpackers


7. Training Photo


8. Training Room with Full AC Facilities and multimedia


9. Once lunch and twice coffeebreak every day of training


10. Qualified  instructor


11. Transportation for participants from hotel of participants to/from venue of training(if minimal number of participants from one company is 4 persons)